How To Clone a Hard Drive..?
Check this Out..!!
Did know that you could clone your current Hard Drive without having to by extra software? Maybe you didn't know that all that you needed, was already set up on your current system? Well, it is... and if you follow this tut, you shouldn't have much of a problem.Make sure that you have a Master and a Slave setup on your system. The Slave drive, in this case, is where all the data on the Master is going to go to.
First: Perform a Scandisk your Master drive and follow that with a thorough Defrag. If you have an Antivirus program, do a thorough sweep with the AV first, then do the Scandisk, followed by the Defrag.
Second: Do the same thing to the target drive, as you did the Master: Scandisk then a thorough Defrag.
Third: Right-click on the Target drive and click on Format. When the box comes up, click your mouse onto the "Full" button.
Fourth: After Formatting the Target drive, run a Scandisk again and click on the button that says "Autofix Errors".
Fifth: In this final part, you might want to cut-and-paste to code in, unless you are sure that you can do it without making any mistakes:
Click on the "Start" button, then click on the "Run..." button, then place the following into the Runbox:
"XCOPY C:\*.*D:\ /c/h/e/k/r" (minus the quotes, of course) then press the "Enter" button.
If you receive an error message, then remove the space from between XCOPY and C:\
Anything that should happen to come up in the DOS box, just click "Y" for "Yes". When its all finished, pull the original Master from the system, designate the Slave as the Master (change your jumpers), then check your new Master out.
This tut has worked and has been tested on all systems except for Windows 2000, so you really shouldn't have any problems. If, by any chance, you should come across a snag, message me and I'll walk you through it.
Check this Out..!!
( WinXP PRO Only)
1) Click Start, Run and enter GPEDIT.MSC
2) Go to Computer Configuration, Administrative Templates, System.
3) Locate the entry for Turn autoplay off and modify it as you desire. Speed Up Browsing
When you connect to a web site your computer sends information back and forth. Some of this information deals with resolving the site name to an IP address, the stuff that TCP/IP really deals with, not words. This is DNS information and is used so that you will not need to ask for the site location each and every time you visit the site. Although Windows XP and Windows XP have a pretty efficient DNS cache, you can increase its overall performance by increasing its size. You can do this with the registry entries below:
Windows Registry Editor Version 5.00
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Dnscache\Parameters]
"CacheHashTableBucketSize"=dword:00000001
"CacheHashTableSize"=dword:00000180
"MaxCacheEntryTtlLimit"=dword:0000fa00
"MaxSOACacheEntryTtlLimit"=dword:0000012d
Make a new text file and rename it to dnscache.reg. Then copy and paste the above into it and save it. Merge it into the registry.
DISABLE INDEXING SERVICES
Indexing Services is a small little program that uses large amounts of RAM and can often make a computer endlessly loud and noisy. This system process indexes and updates lists of all the files that are on your computer. It does this so that when you do a search for something on your computer, it will search faster by scanning the index lists. If you don't search your computer often, or even if you do search often, this system service is completely unnecessary. To disable do the following:
1. Go to Start
2. Click Settings
3. Click Control Panel
4. Double-click Add/Remove Programs
5. Click the Add/Remove Window Components
6. Uncheck the Indexing services
7. Click Next
OPTIMISE DISPLAY SETTINGS
Windows XP can look sexy but displaying all the visual items can waste system resources. To optimize:
1.Go to Start
2. Click Settings
3. Click Control Panel
4. Click System
5. Click Advanced tab
6. In the Performance tab click Settings
7. Leave only the following ticked:
- Show shadows under menus
- Show shadows under mouse pointer
- Show translucent selection rectangle
- Use drop shadows for icons labels on the desktop
- Use visual styles on windows and buttons
SPEEDUP FOLDER BROWSING
You may have noticed that everytime you open my computer to browse folders that there is a slight delay. This is because Windows XP automatically searches for network files and printers everytime you open Windows Explorer. To fix this and to increase browsing significantly:
1. Open My Computer
2. Click on Tools menu
3. Click on Folder Options
4. Click on the View tab.
5. Uncheck the Automatically search for network folders and printers check box
6. Click Apply
7. Click Ok
8. Reboot your computer
REMOVE THE DESKTOP PICTURE
Your desktop background consumes a fair amount of memory and can slow the loading time of your system. Removing it will improve performance.
1. Right click on Desktop and select Properties
2. Select the Desktop tab
3. In the Background window select None
4. Click Ok
DISABLE UNNECESSARY SERVICES
Because Windows XP has to be all things to all people it has many services running that take up system resources that you will never need. Below is a list of services that can be disabled on most machines:
Alerter
Clipbook
Computer Browser
Distributed Link Tracking Client
Fast User Switching
Help and Support - (If you use Windows Help and Support leave this enabled)
Human Interface Access Devices
Indexing Service
IPSEC Services
Messenger
Netmeeting Remote Desktop Sharing (disabled for extra security)
Portable Media Serial Number
Remote Desktop Help Session Manager (disabled for extra security)
Remote Procedure Call Locator
Remote Registry (disabled for extra security)
Remote Registry Service
Secondary Logon
Routing & Remote Access (disabled for extra security)
Server
SSDP Discovery Service - (Unplug n' Pray will disable this)
Telnet
TCP/IP NetBIOS Helper
Upload Manager
Universal Plug and Play Device Host
Windows Time
Wireless Zero Configuration (Do not disable if you use a wireless network)
Workstation
To disable these services:
Go to Start and then Run and type "services.msc"
Doubleclick on the service you want to change
Change the startup type to 'Disable"
REMOVE ANNOYING DELETE CONFIRMATION MESSAGES
Although not strictly a performance tweak I love this fix as it makes my machine 'feel' faster. I hate the annoying 'are you sure?' messages that XP displays, especially if I have to use a laptop touchpad to close them. To remove these messages:
1. Right-click on the 'Recycle Bin' on the desktop and then click 'Properties'
2. Clear the 'Display Delete Confirmation Dialog' check box and click 'Ok'
If you do accidently delete a file don't worry as all is not lost. Just go to your Recycle Bin and 'Restore' the file.
Creating a desktop shortcut for locking your computer
If you use your computer in an area where others may have access to it, and there are things on your system you would rather have kept confidential,locking your desktop when you leave the computer is an essential task. Here's a recipe for a desktop shortcut that will lock your computer in two easy clicks:
Right click on an empty area of the desktop and choose 'new' then 'shortcut.' The create shortcut wizard will open; in the first text box, type '%windir%\System32\rundll32.exe user32.dll,LockWorkStation' and then give your shortcut an appropriate name on the next page, and hit 'finish.'
You will notice that the shortcut you created has a blank icon. To select a more appropriate one, right click on the shortcut and hit 'properties.' In the 'shortcut' tab, click the 'change icon' button.
In the 'look for icons in this file' box, type '%SystemRoot%\system32\SHELL32.dll' then click 'ok' to see a range of icons for your new shortcut. Choose an appropriate icon. Your desktop locking shortcut is now ready for use. Test it out.
Note: It is useful if u have an account as it will prompt for a password.
OR
Hide all drives in my computer
Wanna how your geekiness. Here's the registry hack to hide all the drives in my computer.
head up to
HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\Explorer
create a new DWORD value as NoDrives and modify its data to 03FFFFFF(six F's)
reboot and you are done.
To change back.
delete the key or modify the data to 0. (zero)
When you download photos from your digital camera, they often have unrecognizable names. You can rename several similar files at once with the following procedure. This also works for renaming other types of files.
1.Open the My Pictures folder. (Click Start, and then click My Pictures.) Or open another folder containing files that you want to rename.
2.Select the files you want to rename. If the files you want are not adjacent in the file list, press and hold CTRL, and then click each item to select it.
3.On the File menu, click Rename.
4.Type the new name, and then press ENTER.
All of the files in the series will be named in sequence using the new name you type. For example, if you type Birthday, the first will be named Birthday and subsequent files in the series will be named Birthday (1), Birthday (2), and so on. To specify the starting number for the series, type the starting number in parentheses after the new file name. The files in the series will be numbered in sequence starting with the number you type. For example, if you type Birthday (10), the other files will be named Birthday (11), Birthday (12), and so on.
Today that the virus once it much ..?
pnyebarannya many ways, there are also through autorun, to be bored once I fix ..
have been repaired, a friend plug FlashDisk More entrance, repaired again, so tireedd ..
Because the better to prevent than treat today, I autorun the computer to disable ALL Drive, could already know how ..?
the following way ..
1. Open the "Run" Type "gpedit.msc" without the quotation marks
2. and then you select the "Computer Configuration" again and select "Administrative Templates" Select "System"
3. Select "Turn off Autoplay"
4. Select the "Enabled" Then underneath a select "All drives"
now completed ..
99,9% now your computer safe from the spread of the virus, which run through the autorun self
- Check software version *888*837#
I-mobile 100 ,200 , 313
- Check software version #*888#
I-mobile 309, 310
- Check software version *0*4636#
- Test Mode *0*6268#
I-mobile 311
- Check software version #*878#
I-mobile 511
- Check software version *1222*1#
I-mobile 301, 302,308, 508, 601, 602, 603, 604, 606, 611, 901, 902
- Check software version *#159#
- Set Factory Mode *#32787#
- Set Engineer Mode *#3646633#
I-mobile 503, 506, 605, 600, 607, 608
- Set Engineer Mode ***503#
- Set Factory Mode ***504#
- Set Auto Test ***505#
I-mobile 509, 612
- Set Factory Mode *#66*#
I-mobile 504, 505, 803
- Check software version *68*48#
- Set full factory *789#
- Test Mode *#789#
I-mobile 305, 306, 315, 510, 609, 609i,516
- Check software version *#8375#
- Set Factory Mode 878
I-mobile 610
- Check software version *#22#
I-mobile J101, J102
- Test Mode *23638777*783781#
I-mobile 502, 502i, 505, k9, 802
- Check software version *201206*4636#
Restore factory settings: *#987*99#
LCD contrast: *#369#
software version: *#800#
software version: *#900#
set default language: *#0000# Send
set English language: *#0044# Send
set English language (new firmware): *#001# Send
default user code: 1122, 3344, 1234, 5678
Engineer mode: *#110*01#
Factory mode: *#987#
Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
Credits To
http://forum.gsmhosting.com/vbb/archive/index.php/t-457115.html
CHINESE MODELS:
default user code: 1122, 3344, 1234, 5678
Engineer mode: *#110*01#
Factory mode: *#987#
Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
Restore factory settings: *#987*99#
LCD contrast: *#369#
software version: *#800#
software version: *#900#
set default language: *#0000# Send
set English language: *#0044# Send
set English language (new firmware): *#001# Send
*#66*# Set Factory Mode CONFIRMED
*#8375# Show Software Version CONFIRMED
*#1234# A2DP ACP Mode CONFIRMED
*#1234# A2DP INT Mode CONFIRMED
*#0000# + Send : Set Default Language CONFIRMED
*#0007# + Send : Set Language to Russian CONFIRMED
*#0033# + Send : Set Language to French CONFIRMED
*#0034# + Send : Set Language to Spanish CONFIRMED
*#0039# + Send : Set Language to Italian CONFIRMED
*#0044# + Send : Set Language to English CONFIRMED
*#0049# + Send : Set Language to German CONFIRMED
*#0066# + Send : Set Language to Thai CONFIRMED
*#0084# + Send : Set Language to Vietnamese CONFIRMED
*#0966# + Send : Set Language to Arabic CONFIRMED
More some codes for reset mobile china
*#77218114#
*#881188#
*#94267357#
*#9426*357#
*#19912006#
*#118811#
*#3646633#
CHINESE MODELS:
default user code: 1122, 3344, 1234, 5678
Engineer mode: *#110*01#
Factory mode: *#987#
Enable COM port: *#110*01# -> Device -> Set UART -> PS Config -> UART1/115200
Restore factory settings: *#987*99#
LCD contrast: *#369#
software version: *#800#
software version: *#900#
set default language: *#0000# Send
set English language: *#0044# Send
set English language (new firmware): *#001# Send
Credits To Muhammad Afzal Meo
Service codes GStar:
GM208 (Chinese Nokea 6230+) engineering menu: *#66*#
Set language to English: *#0044#
Set language to Russian: *#0007#
Credits To
http://forum.gsmhosting.com/vbb/archive/index.php/t-457115.html
Service codes Konka:
C926 software version: *320# Send
C926 set default language: *#0000# Send
C926 set English language: *#0044# Send
Credits To
http://forum.gsmhosting.com/vbb/archive/index.php/t-457115.html
Service codes Fly:
M100 software version: ####0000#
2040(i) reset defaults: *#987*99# Send
MX200 reset defaults: *#987*99# Send
MX200 software version: *#900# Send
SL300m reset defaults: *#987*99# Send
SL300m software version: *#900# Send
SL500m reset defaults: *#987*99# Send
SL500m software version: *#900# Send
MP500 reset defaults: *#987*99# Send
MP500 software version: *#900# Send
Set language to English: *#0044#
Set language to Russian: *#0007#
Credits To
http://forum.gsmhosting.com/vbb/archive/index.php/t-457115.html
Service codes Motofone-F3:
Motofone F3 software version: **9999* Send
***300* Set SIM Pin
***310* / ***311* SIM Pin ON | OFF
***000* Reset Factory settings
***644* Set Voicemail number
***260* / ***261* Auto keypad lock ON | OFF
***510* / ***511* Voice Prompts ON | OFF
***160* / ***161* Restricted Calling (Phonebook only) ON | OFF
***200608* Send: software version
***200606* Send: software version
***200806* Send: flex version
***250* / ***251* Keypad tones ON | OFF
***470* Select time format
***500* /***501* Prepaid Balance Display ON | OFF
***520* Change language
Credits To
http://forum.gsmhosting.com/vbb/archive/index.php/t-457115.html
Service codes LG:
software version: 2945#*#
KG300 NVRAM format: 2945#*# -> menu 15
Credits To
http://forum.gsmhosting.com/vbb/archive/index.php/t-457115.html
Service codes BenQ:
software version: *#300#
test mode: *#302*20040615#
Credits To
http://forum.gsmhosting.com/vbb/archive/index.php/t-457115.html
Service codes Pantech:
software version: *01763*79837#
service menu: *01763*476#
reset defaults (phone/user code reset to default): *01763*737381#
Service codes VK-Mobile 3xx, 5xx:
software version: *#79#
software version: *#837#
service menu: *#85*364# (hold #)
Service codes VK200, VK2000, VK2010, VK2020, VK4000:
software version: *#79#
service menu: *#9998*8336# (hold #)
reset defaults (phone/user code reset to default): *#9998*7328# (hold #)
Credits To
http://forum.gsmhosting.com/vbb/archive/index.php/t-457115.html
ZTE Mobile
1- *938*737381#
2- PHONE WILL DIPLAYED DONE
3- POWER OFF YOUR PHONE AND POWER ON AGAIN
Credits To
http://forum.gsmhosting.com/vbb/archive/index.php/t-457115.html
Motorola V3688
IMEI *#06#
Enhanced Full Rate Codec EFR
Enable EFR : [][][] 119 [] 1 [] OK.
disable EFR : [][][] 119 [] 0 [] OK
Credits To Mobile Centre Universal
!!! Sim Lock [10 digits code ] ( it could harm your phone )
NETWORK : OPTION NOT AVAILABLE
Test LCD: display test of the green/red leds and vibration
Push * and type 4329 :enables/disables network monitor 1 (the same of MT35)
Push * and type 621342 :enables/disables network monitor 2
Push * and type 5807 : Serial Number Software Vers.
Push * and type 936505: IMEI -- Software Vers.
TPush * and type 547 : Test serial Data Cable DISPLAYS :"Testmode"
Push * and type 362628: ISMI BLOCK (UNKNOWN)
Push * and type 476989: NS BLOCK (UNKNOWN)
Push * and type 482896:CP BLOCK (UNKNOWN)
Push * and type 787090: ? BLOCK (UNKNOWN)
Push * and type 787292 : block current network
!!! Push * and type 967678: SP LOCK!!!
Push * and type 850696:Warm Start ( ENABLE/DISABLE)
Push * and type 3926 : Swicth off phone
Push * and type 5806: Production date and SW version
Credits To Mobile Centre Universal
Sony CMD Z5/J5
Vers. SW :
Without SIM , switch on phone and type l *#7353273#
Credits To Mobile Centre Universal
Sagem MC959/940
Select commands' menu and push *
Displays a new menu' :
Appli : software vers. and battery's voltage
Eprom
Sim Lock
Test LCD: display test , green/red and vibration
Sagem MC920
Select commands' menu and push *
Displays 5 new menus :
1 APPLI
VERSION ( SW)
BATTERY (voltage )
2 PROM (IMEI)
3!!! SIM LOCK (10 digits code requested ) !!!
4- NETWORK (returns : OPTION NOT AVAILABLE)
5- TEST LCD
SYMBOL 1 (LCD)
SYMBOL 2 (test2 LCD)
BLACK (all icons and carachters displayed )
FOR PHOTO (welcome message and time )
VIBRATOR (vibration test )
Credits To Mobile Centre Universal
Telit GM 810 MONITOR - technical menu - : type ++++ and push OK.
Adiacent cells list : # and *
Now if you push OK the phone displays battery ' s voltage and temperature
Credits To Mobile Centre Universal
Trium Geo/Geo @ - Astral - Cosmo -AriaEnter the menu and type *
A new menu will be displayed :
Application : SW version and battery's voltage
Trium Galaxy
Push * and type 5806: Production date and SW version
Credits To Mobile Centre Universal
NEC db2000 *#2820# software vers.
IMEI *#06#
Reset *73738# (send?)
SP Lock info:
* # 3210 # (send?)
Network barring info : *#8140# (send?)
( it could harm your phone )
SIM lock it could harm your phone )
*#4960 # (send?) -Inquiry * 4960 * password * password # (send?) lock
#4960* password # (send?) unlock
[password] [8 digits]
Net Lock
*#7320# (send?) -Inquiry * 7320 * password * password # (send?) lock
#7320* password # (send?) unlock
[password] [ 8 digits]
Net Lock 2:
*#2220# (invio) - Inquiry * 2220 * password * password # (send?) lock
#2220* password # (invio?)unlock
[password] [8 digits]
Unlock subnetwork
*#1110# (send?) - inquiry * 1110 * password * password # (send?) lock
#1110* password # (send?) unlock
[password] [n� 8 cifre]
( it could harm your phone )
Credits To Mobile Centre Universal
Acer V 750
*#400# Display Adc/ Set Cal-Value -
*#402# Set LCD Contrast
*#403# Display Errors Info
*#300# Display Info Hw & Sw
*#301# Menu Test
*#302# Menu Acoustics
*#303# (Settings saved) Set English language?
*#307# Menu Engineering
*#311# Reset Phone Code - [ Also reset Security Codes ! ]
*#330# (Execute not success) [ unknown ]
*#331# (Service deactivated) [ unknown ]
*#332# (Service unavailable)[ unknown ]
*#333# (Execute not success)[ unknown ]
*#351# (Service unavailable) [ unknown ]
*#360# (Invalid input)[ unknown ]
*#361# (Invalid input) [ unknown ]
*#362# (Invalid input) [ unknown ]
#363# (Invalid input) [ unknown ]
Credits To Mobile Centre Universal
Genie DB *#06# IMEI.
*#2254*# Near Cell Mode.For every received BTS will be displayed :
Current channel and 2 channel levels
*#06# IMEI
*#2558# time of network connection ( D/H/M )
*#2562# Fores reconnection to network
!!!*#7489# Dispalys and modify phones' security code!!!
!!!*#3377# SIM lock information !!!
*#7378# SIM card Informations : supported phase name and tipe
*#7693# Enable/disable "Sleep Mode"
*#8463# State of "Sleep Mode"
*#2255# Debug Call Mode enable/disable
*#3333*# Displays the blocking list.
*#7489*# Displays the security code
*#06# Displays the IMEI number
*#8377*# Displays the SW info.
Credits To Mobile Centre Universal
Panasonic
Panasonic gd90 gd93
*#9999# SW - Type the code on switch on , during network seek-Vers. SW and production code Enable ringing and vibration contemporarily Enable vibration with # then increase volume with "tone menu "
Panasonic gd70
*#9999# SW - Type the code on switch on , during network seek-Vers. SW and production code Enable ringing and vibration contemporarily Enable vibration with # then increase volume with "tone menu "
Credits To Mobile Centre Universal
Philips
*#3333*# Displays the blocking list.
*#7489*# Displays the security code.
*#06# Displays the IMEI number.
*#8377*# Displays the SW info.
Credits To Mobile Centre Universal
Samsung SGH600/2100DB IMEI number: * # 0 6 #
Software version: * # 9 9 9 9 # albo * # 0 8 3 7 #
Net Monitor: * # 0 3 2 4 #
Chaning LCD contrast: * # 0 5 2 3 #
Memory info: * # 0 3 7 7 # albo * # 0 2 4 6 #
Reset pamieci (SIMLOCK`a removing!!!): *2767*3855#
Reset pamieci CUSTOM: *2767*2878#
Battery state: * # 9 9 9 8 * 2 2 8 #
Alarm beeper: *#9998*289#
Vibra test: *#9998*842#::.
IMEI number: * # 0 6 #
Software version: * # 9 9 9 9 #
Credits To Mobile Centre Universal
ALCATEL
IMEI number: * # 0 6 #Software version: * # 0 6 #
Net Monitor: 0 0 0 0 0 0 *
Credits To Mobile Centre Universal
Bosch
IMEI Number: * # 0 6 #
Dafault Language: * # 0 0 0 0 #
Net Monitor: * # 3 2 6 2 2 5 5 * 8 3 7 8 #
Credits To Mobile Centre Universal
Siemens C25
IMEI number: * # 0 6 #
Software version: put off sim card and enter: : * # 0 6 # and press LONG KEY Bonus screen: in phone booke: + 1 2 0 2 2 2 4 3 1 2 1
Credits To Mobile Centre Universal
Ericsson
Ericson T65
*#05# Fake Insert puk screen Press no to exit
Ericsson T20
MENU tecnichal Info
[type] >*<<*<* Displays : 1] Info service 1] Info SW 2] Info hardware 3] SIMlock 4]setup 2] Service setup 1] Contrast 3]Service Test 1] Display 2]Leds 3]Keyboard 4] ringer 5] Vibration 6]Headset 7] Microphone 8]Clock 4] Names List MENU info [Type] >*<<**<>*<<*<* menu Tecnichal info SW vers. and name list >*<<**<> are the right and left menu's keysEricsson T18s/T10/A1018s
>*<<*<* software CXC125065 Internal product code PRG 970715 1515 Software version and SW rev.<* CLR <><**>*<<*<*> Displays texts and messages in the phone It will be displayed " TEXT " then push YES <> are the right and left menu's keys !!!><** Control /Enable SIM Lock!!! Ericsson R310 Technical Info : >*<<*<*Options : 1) service Info info Software Simlock Configuration 2) Service Test Display Led/Illumination Keyboard ringer Vibration Headset Microphone Clock 3)Text's name List Info personal : >*<<**< SIM Locking ( 8 digits' code ) ( it could harm your phone )
1) Network
2) Subnetwork
3) SP
4) Corporate
Credits To Mobile Centre Universal
Sony Ericsson Secret Menu: -> * <- <- * <- *
(-> means press joystick, arrow keys or jogdial to the right and <- means left.) You'll see phone model, software info, IMEI, configuration info, sim lock status, REAL time clock, total call time and text labels. You can also test your phones services and hardware from this menu (main display, camera, LED/illumination, Flash LED, keyboard, earphone, speaker, microphone, radio and vibrator tests)
Sony-Ericsson:
J100 software version: #82#
Only it
Credits to Mobile Centre Universal
3370# Activate Enchanced Full Rate Codec (EFR) Your phone uses the best sound quality but talk time is reduced my approx.5%.
#3370# Deactivate Enchanced Full Rate Codec (EFR)
*#4720# Active Half Rate Codec � Your phone uses a lower quality sound but you should gain approx 30% more Talk Time
*#4720# Deactivate Half Rate Codec
*#0000# Displays your phones software version, 1st Line : Software version, 2nd Line : Software Release Date, 3rd Line : Compression Type
*#9999# Phones software version if *#0000# does not work
*#06# For checking the International Mobile Equipment Identity IMEI Number)
#pw+1234567890+1# Provider Lock Status (use the" button to obtain the"p,w"symbols)
#pw+1234567890+2# Network Lock Status (use the" button to obtain the"p,w"symbols)
#pw+1234567890+3# Country Lock Status (use the" button to obtain the"p,w"symbols)
#pw+1234567890+4# SIM Card Lock Status (use the" button to obtain the"p,w"symbols)
#147# ( vodofone ) this lets u know who called you last
*#1471# Last call (only vodofone)
*#21# Allows U to check the number that " all calls" are diverted to
*#2640# Displays security code in use
*#30# Lets you see the private number
*#43# Allows yot to check the "Call Waiting" status of your phone.
*#61# Allows you to check the number that" On No Reply" calls are diverted to
*#62# Allows you to check the number that" Divert IF Unreachable (no service)" calls are diverted to
*#67# Allows you to check the number that" On Busy Calls"are diverted to
*#67705646# Removes oprator logo on 3310 & 33330
*#73# Reset phone timers and game scores
*#746025625# Displays the SIM Clock status, if your phone support this power saving feture" SIM clock Stop Allowed" it means you will get the best standby time possible.
*#7760# Manufactures Code
*#7780# Restore factory settings
*#8110# Software version fot the Nokia 8110
*#92702689# Displays-1. Serial Number, 2.Date Made, 3. Purchase Data, 4.Date of last repair (0000 for no repairs), 5.Transfer Used Data,to exit this made you need to switch your phone off then on gain.
*#94870345123456789# Deactive the PWM-Mem
**21*number# Turn on" All calls" diverting to the phone number entered
**61*number# Turn on" No Reply" diverting to the phone number entered
**67*number# Turn on" On Busy" diverting to the phone number entered
12345 This is the default security code, press and hold #
Lets you switch between lines
Credits to Nokia Centers
* *#06# for checking the IMEI (International Mobile Equipment Identity).
* *#7780# reset to factory settings.
* *#67705646# This will clear the LCD display
* *#0000# To view software version.
* *#2820# Bluetooth device address.
* *#746025625# Sim clock allowed status.
* *#62209526# - Display the MAC address of the WLAN adapter. This is available only in the newer devices that supports WLAN like N80
* #pw+1234567890+1# Shows if sim have restrictions.
*#92702689# - takes you to a secret menu where you may find some of the information below:
* 1. Displays Serial Number.
* 2. Displays the Month and Year of Manufacture
* 3. Displays (if there) the date where the phone was purchased (MMYY)
* 4. Displays the date of the last repair - if found (0000)
* 5. Shows life timer of phone (time passes since last start)
*#3370# - Enhanced Full Rate Codec (EFR) activation. Increase signal strength, better signal reception. It also help if u want to use GPRS and the service is not responding or too slow. Phone battery will drain faster though.
*#3370* - (EFR) deactivation. Phone will automatically restart. Increase battery life by 30% because phone receives less signal from network.
*#4720# - Half Rate Codec activation.
*#4720* - Half Rate Codec deactivation. The phone will automatically restart
If you forgot wallet code for Nokia S60 phone, use this code reset: *#7370925538#
Note, your data in the wallet will be erased. Phone will ask you the lock code. Default lock code is: 12345
Press *#3925538# to delete the contents and code of wallet.
*#7328748263373738# resets security code.
Default security code is 12345
Unlock service provider: Insert sim, turn phone on and press vol up(arrow keys) for 3 seconds, should say pin code. Press C,then press * message should flash, press * again and 04*pin*pin*pin#
Change closed caller group (settings >security settings>user groups) to 00000 and ure phone will sound the message tone when you are near a radar speed trap. Setting it to 500 will cause your phone 2 set off security alarms at shop exits, gr8 for practical jokes! (works with some of the Nokia phones.)
Press and hold “0″ on the main screen to open wap browser.
Credits to Nokia Centers
Tired see your desktop background that is only? Here I have a few tricks that the desktop background that you can keep changing every time you refresh me-desktop. ^ ^
how? let see ...
Create a new folder, you type "but the script below, and to Sign folder:
CODE
CODE
<html>
<head>
<title>RandomDesktopWallpaper</TITLE>
</head>
<body>
<script language="JavaScript">
<!--
var imagenumber = 15;
var randomnumber = Math.random();
var rand1 = Math.round((imagenumber-1)*randomnumber)+1;
images = new Array
images[1]="1.jpg"
images[2]="2.jpg"
images[3]="3.jpg"
images[4]="4.jpg"
images[5]="5.jpg"
images[6]="6.jpg"
images[7]="7.jpg"
images[8]="8.jpg"
images[9]="9.jpg"
images[10]="10.jpg"
images[11]="11.jpg"
images[12]="12.jpg"
images[13]="13.jpg"
images[14]="14.jpg"
images[15]="15.jpg"
var image = images[rand1]
//-->
document.write('<body background="'+image+'">')
</script>
</body>
</html>
Save with refresh.htm name or any name it, but the extensions should be *. htm
Imagenumber line var = 15; it can be changed depending on how many pictures you want to input, for example, over 15 input image I have of my rename 1-15.
Find the picture you like (the amount) to put the folder that was over, and rename your pictures using numbers that the time would easily edit scriptnya later. Perhatikann also extensions. Jpg. Gif. Png and other dot dot. (.)(.)
Now how ngeloadnya! Didesktop right click, select properties, desktop, click browse, find the folder that was refresh.htm select and then click open, will appear white dimonitornya. Then click Apply again does OK. Continue to try to refresh your desktopnya, certainly changed the picture now! Have fun ...
/ NoGe / Evilcode
The following is the key to the secret key code that can run your own type in your phone's keypad hp that the Nokia brand, which both CDMA and GSM;
1. See the IMEI (International Mobile Equipment Identity)
By the way, press * # 0 6 #
2. See the version of the software, making softwre date and type of compression software
By the way, press * # 0 0 0 0 #
If not successful try e * # 9 9 9 9 #
3. Viewing the status of call waiting
By the way, press * # 4 3 #
4. See the number / number of private number to contact your mobile phone
By the way, press * # 3 0 #
5. Showing phone number diverts all calls
By the way, press * 2 1 # #
6. See the number on the transfer of telephone callers because you do not answer (call divert on)
By the way, press * 6 1 # #
7. See the number callers on the phone because it diverts outside the reach (call divert on)
By the way, press * # 6 2 #
8. See the number on the transfer of the callers because of busy phone (call divert on)
By the way, press * # # 6 7
9. Changing the logo on the service type nokia 3310 and 3330
By the way, press * # 6 7 7 0 5 6 4 6 #
10. Showing the status of the SIM clock
By the way, press * # 7 4 6 0 2 5 6 2 5 #
11. Switching to profile your phone profile
How to press the power button off without arrested
12. Changing the setting hp nokia to default or manufacturer
By the way, press * # 7 7 8 0 #
13. Conducting reset the timer mobile phone games and score nokia
By the way, press * # # 7 3
14. Viewing the status of call waiting
By the way, press * # 4 3 #
15. Viewing the code factory or factory code
By the way, press * # 7 7 6 0 #
16. Showing a serial number or serial number hp, making the date, the date of purchase, the last date of service, transfer of user data. To exit the phone must be reset again.
By the way, press * # 92702689 #
17. Security code to see your mobile phone
By the way, press * # 2 6 4 0 #
18. See ip address your hardware bluetooth
By the way, press * # 2 8 2 0 #
19. Activate the EFR with the best sound quality but the lavish energy batteries. To turn off using the same code.
By the way, press * # 3 3 7 0 #
20. EFR activate the sound quality but the lowest energy-efficient batteries. To turn off using the same code.
By the way, press * # 4 7 2 0 #
21. Towards the contents of phone book quickly in the mobile phone nokia
How serial number and press # example: 150 #
22. Switch the call to the number that it's correct to call all
By the way, press * * 2 1 * # Tax Goal
23. Switch the call to the number that it's correct to call the missed
By the way, press * * * 6 1 Tax Goal #
24. Switch the call to the number that it's correct for phone calls when you are busy hp
By the way, press * * * 6 7 Tax Goal #
Additional Information:
- Code diinput without a space
- There is a code nokia applicable only in certain types of
Credits to Nokia Centers
many people that often have problem about this ,
i shall study here. .
now:
>> open notepad or text another editor
>> write script next:
[version]
signature=" assasinboy"
provider=donnyboy
[defaultinstall]
addreg=unhookregkey
delreg=del
[unhookregkey]
hklm, software\classes\batfile\shell\open\command, , , " " " %1" " %*"
hklm, software\classes\comfile\shell\open\command, , , " " " %1" " %*"
hklm, software\classes\exefile\shell\open\command, , , " " " %1" " %*"
hklm, software\classes\piffile\shell\open\command, , , " " " %1" " %*"
hklm, software\classes\regfile\shell\open\command, , , " regedit. exe" %1" "
hklm, software\classes\scrfile\shell\open\command, , , " " " %1" " %*"
hklm, software\microsoft\windows nt\currentversion\winlogon, shell, 0, " explorer. exe"
hklm, system\controlset001\control\safeboot, alternateshell, 0, " cmd. exe"
hklm, system\controlset002\control\safeboot, alternateshell, 0, " cmd. exe"
hklm, system\currentcontrolset\control\safeboot, alternateshell, 0, " cmd. exe"
[del]
hkcu, software\microsoft\windows\currentversion\policies\system, menyableregistrytools
hklm, software\microsoft\windows\currentversion\policies\system, menyableregistrytools
hklm, software\microsoft\windows nt\currentversion\image file
execution options\regedit. exe
>> after finished, save by the name of repair. inf
>> then, click right, install and happy. .
Huy, halo all I want to show some way to hide the file to the image
such as how to do this:
1. Set your windows to show the file extension. Open the Control Panel and click the 2X in the Folder Options.
Go to the View tab and then removed the check on the option Hide extensions for known file types
2. Prepare your secret file (the file extension), for example, has a name Yellowcard.mp3 and an image file (*. bmp, *. jpg, gif *), for example with the name Naruto.jpg. Keep these two files in a directory the same.
3. Right-click on the file menu and select Yellowcard.mp3 [Add to Yellowcard.rar]. Will create a new file with the name Yellowcard.rar
4. Now, open the application Notepad (Start -> Run type notepad) and type the following script:
@ echo off
ren Yellowcard.rar Yellowcard.mp3.rar
copy / b Naruto.jpg Yellowcard.mp3.rar Hasil.jpg
del Yellowcard.mp3
del Naruto.jpg
del Yellowcard.mp3.rar
del hide.bat
Remember! Adjust the names of the files on the script above the name of your file (except hide.bat). Note also the following line:
ren Yellowcard.rar Yellowcard.mp3.rar
The format of writing: Ren namafileanda.rar namafileanda.ekstensi sebelumnya.rar
So, for example, if your file is rahasia.exe before and after the rar into rahasia.rar, the book is:
ren rahasia.rar rahasia.exe.rar
Note also the name of the file hasil.jpg. Change hasil.jpg become hasil.ekstensi_file_gambar_anda. So, for example, image files that you use to hide the secret files is naruto.gif later, the change hasil.jpg become hasil.gif
Well, keep this file in the same location with the files you say. Click [File] [Save] and then in the form field type the file name hide.bat Meanwhile, in the Save as type select â € ~ All filesâ € ™. Click [Save] afterwards.
5. Close all windows that open programs. Now, open the folder where you store all the files overnight. double-click on the file hide.bat. Wait until the shadow windows immediately command processor appear. If successful, all the files in the folder will disappear replaced with a new file named hasil.jpg
Try hasil.jpg you open the file. Overview there will be no difference with the file pemandangan.jpg property unless you increase the size of the file that big. You can still open the file with the Picture Editor or Image Viewer pity you. There are no signs that there is actually a secret inside of it .. wink.gif
And, then, where my confidential files? Relax, do not panic! Right-click on the file and choose hasil.jpg [Open With] - [Choose Program ..]. Choose WinRar then click [OK].
check this Out..!!
write this script in notepad, and name "protect.vbs"
on error goto 0
dim s, QUEST, sd, m, winpath, fs
to set = createobject ( "Wscript.shell")
set fs = createobject ( "Scripting.FileSystemObject")
set winpath = fs.getspecialfolder (0)
set wscript.createobject s = ( "wscript.shell")
QUEST do while = ""
QUEST = inputbox ( "Enter the keyword!", "Validation")
QUEST if = "" then
m = MsgBox ( "Sorry, you must enter the keyword", 0+0+48, "Caution")
end if
loop
if QUEST = "password" then
s.run "shutdown -a"
sd.run winpath & "\ explorer.exe / e, / select," & Wscript.ScriptFullname
else
s.run "shutdown-s-t 5-c Sorry_Wrong_Password"
end if
change the password to change over to the writing "password" (without the sign ") between the script" if QUEST = "password" then "(without the sign") will be
and then again in notepad write the script below, and give the name "autorun.inf"
[autorun]
shellexecute = wscript.exe protect.vbs
power to create ..
now a lot of virus one of the the effect can make document or our folder losts. . ! !
may be we estimate that document or folder lost permanent, don't take decision formerly. .
try you can investigate via command prompt (cmd),
with typing e: (if drive that we repair drive e: )
so now position drive is bing
e: \>
then type mer/a to investigate to what document or folder still there or lost permanent, be
e: \>dir/a
if still there, mean your destiny stills luck. .
hhaaaaahahaha. .
but if there is no hope to sorrow, hhhahahhhhahaha. .
manner return it with mengeti attrib -s -h /d /s, so be
e: \>attrib -s -h /d /s
hope wait a minute, because this process is enough wants time. .
and if finished, so will return to be
e: \>
well, now document or your file has returned to originally